Design2Part Expo Logo

Join Bales at the DESIGN-2-PART Expo

April 20, 2026

Pitting and Corrosion in Injection Molds: Causes and Prevention

November 19, 2026

Hard Chrome Plating vs. Stainless Steel for Molds and Industrial Parts

Mold builders and manufacturers often ask the same question when they spec a new tool or replace a worn one: is it better to build the part from stainless steel, or to build it from a tool steel and protect it with hard chrome plating? The answer depends on what is wearing the part out: corrosion, abrasion, sticking, or all three. This guide explains the trade-offs and when a coating such as hard chrome or electroless nickel is the better choice.

The short answer

  • Choose stainless steel when corrosion is the main risk across the whole part, wear is moderate, and the higher material and machining cost is acceptable.
  • Choose tool steel with hard chrome plating when the working surface sees heavy abrasion or sliding wear, you need a very hard, low-friction surface, or you want to restore a worn part to size instead of replacing it.
  • Choose electroless nickel or a composite nickel coating when you need corrosion protection with uniform thickness on complex shapes, deep cavities, or aluminum.

How stainless steel and hard chrome compare

FactorStainless steel (e.g., 420 mold steel)Tool steel + hard chrome plating
Corrosion resistanceBuilt into the material; can still pit if not properly passivated or exposed to chloridesGood on the plated surface; protection depends on full coverage and coating thickness
Surface hardnessHardened stainless mold steels typically run around the low 50s HRCHard chrome is typically in the high 60s HRC equivalent, much harder than the base steel
Wear and abrasionModerateExcellent, especially against glass-filled and abrasive resins
Friction and releaseModerateLow coefficient of friction helps parts release
RepairWorn surfaces usually require welding or re-machiningWorn chrome can be stripped and replated to restore the surface
CostHigher material and machining costLower-cost base steel plus the plating cost

When stainless steel is the right call

Stainless steel makes sense when the entire tool, including water lines and non-molding surfaces, will see moisture, humidity, or corrosive resins over a long life, and when wear on the molding surface is modest. To get the corrosion resistance stainless is known for, the surface should be clean and passivated after machining. Citric acid passivation removes free iron left from machining and restores the passive oxide layer that protects the part.

When hard chrome plating is the better choice

Hard chrome plating is the go-to when the problem is wear. Glass-filled nylons, mineral-filled compounds, and high-volume production all scrub the molding surface. A hard chrome layer protects the steel underneath, lowers friction for better part release, and can be stripped and replated when it eventually wears, which is usually faster and less expensive than rebuilding the tool. For applications that need extra hardness and release, Diamond Chrome builds on hard chrome performance.

What about electroless nickel?

Hard chrome is applied electrolytically, so thickness can vary on edges and deep features. Electroless nickel deposits a uniform layer everywhere the solution reaches, including deep cavities, threads, and internal passages, and it plates aluminum well. When corrosion protection with even coverage matters more than maximum hardness, electroless nickel or a composite such as Nicklon™ (electroless nickel with PTFE) or Nibore™ (nickel boron) is often the better fit.

Frequently asked questions

Is chrome plating more corrosion resistant than stainless steel?

Not across the board. Stainless steel resists corrosion throughout the material, while hard chrome protects only the plated surface. Hard chrome is chosen mainly for hardness and wear resistance. If corrosion is the main concern, stainless steel, electroless nickel, or a composite nickel coating is usually the better choice.

Can you chrome plate stainless steel?

Yes. Stainless steel parts and molds can be hard chrome plated to add surface hardness and wear resistance where the base material alone is not enough.

Why does my stainless steel mold still rust or pit?

Free iron left on the surface from machining, chlorides, condensation, and corrosive resin off-gassing can all cause rust or pitting on stainless steel. Passivation after machining and a protective coating in high-risk areas help prevent it.

Can a worn chrome-plated mold be repaired?

Yes. Worn hard chrome can be stripped, the surface prepared and polished, and the part replated, which restores the surface without rebuilding the tool.

Not sure which is right for your part?

Bales Metal Surface Solutions in Downers Grove, Illinois, plates and finishes molds and industrial components for manufacturers across the country. Tell us the material, the resin or process, and what is failing, and we will recommend a coating. Request a quote or call (888) 347-7014.