Hard Chrome Plating vs. Stainless Steel for Molds and Industrial Parts

November 19, 2026

Pitting and Corrosion in Injection Molds: Causes and Prevention

Pitting and corrosion are among the most expensive problems a mold can develop. A few small pits on a polished cavity show up on every part, cause sticking and drag, and can turn into scrap, downtime, and a costly rework. This guide covers what causes pitting and corrosion in injection molds and the coatings and finishes that prevent it.

What causes pitting and corrosion in molds

  • Condensation and humidity. Chilled molds pull moisture out of the air, and molds stored in humid plants or shipped in cold weather sweat. Water left on the steel starts rust and pitting quickly.
  • Corrosive resins and additives. PVC, flame-retardant compounds, and some filled and engineering resins release corrosive gases during molding that attack unprotected steel.
  • Water lines and cooling channels. Scale, poor water treatment, and stagnant water corrode cooling passages from the inside, even when the cavity looks fine.
  • Free iron on stainless steel. Machining leaves embedded iron on stainless surfaces. Without passivation, it rusts and can start pitting.
  • Galvanic corrosion. When dissimilar metals touch in the presence of moisture, such as aluminum inserts in steel or beryllium copper components, the less noble metal corrodes faster.
  • Damaged or incomplete plating. Missed spots, racking marks, or worn plating expose the base steel, and corrosion concentrates there.

How to prevent mold corrosion

  • Dry and protect molds before storage, and use a rust preventive between runs.
  • Control plant humidity and avoid running chilled molds below the dew point.
  • Maintain water treatment and flush cooling lines on a schedule.
  • Passivate stainless steel components after machining.
  • Apply a protective coating with full, uniform coverage on molding surfaces exposed to corrosive resins or moisture.

Coatings that protect against pitting and corrosion

Electroless nickel plating deposits a uniform layer on every surface the solution reaches, including deep ribs, cores, and textured areas, and is a common choice to protect molds from corrosive resins and moisture. It also plates aluminum molds well.

Nicklon™ adds PTFE to electroless nickel for corrosion protection plus lubricity, which helps where parts stick. Nibore™, a nickel boron coating, combines release, wear resistance, and protection for demanding applications. Diamond E.N.™ adds hardness for abrasive resins.

For stainless steel, citric acid passivation removes free iron and restores the protective passive layer. For molds that already have light pitting or a dulled finish, mold polishing can restore the surface before a protective coating goes on.

Frequently asked questions

What is the best coating to prevent mold corrosion?

For most injection molds, electroless nickel or a composite electroless nickel coating offers the best balance of uniform coverage and corrosion protection. The right choice depends on the resin, whether parts stick, and how much wear the surface sees.

Can a pitted mold be repaired?

Light pitting can often be polished out and the surface protected with a coating. Deeper pitting may need welding or machining first. A coating specialist can assess the damage and recommend the most cost-effective repair.

Why does stainless steel pit?

Stainless steel pits when chlorides, moisture, or embedded free iron break down its passive surface layer. Passivation after machining and keeping the surface clean and dry reduce the risk.

Does electroless nickel prevent galvanic corrosion?

A continuous electroless nickel layer separates the base metal from moisture and can reduce corrosion where dissimilar metals meet. Full coverage matters, so thickness and coverage should be confirmed for the application.

Protect your molds before pitting starts

Bales Metal Surface Solutions in Downers Grove, Illinois, coats, polishes, and passivates injection molds and industrial components for manufacturers nationwide. Tell us your resin, mold material, and what you are seeing, and we will recommend a solution. Request a quote or call (888) 347-7014.